Roush Rear Leveling Springs Install

joshfrisco · July 3rd, 2009, 08:22 PM

Originally Posted by coolhandluke

Well...I just finally installed my Roush springs and BMR adjustable panhard on Saturday. I'm really pleased with the change in stance. I only swapped the rear springs out for the Roush 1" drop springs that make the gap in the rear match the front. Here are a few comparison pics for those who might be interested in evening up the stance but not dropping the car on all four corners. Total cost between the springs and panhard was $255 shipped. The springs were only $120 of that cost. My rear end was off by 1/4" which was the reason for the adjustable panhard.

Terrible lighting, but you get the idea.

super nice and super clean!

coolhandluke · July 4th, 2009, 10:02 AM

Originally Posted by joshfrisco

super nice and super clean!

Thanks Josh...I would take that rear bumper of yours in a heartbeat.

hellbred07 · July 6th, 2009, 12:43 AM

Got mine on the way.

7upstang · July 6th, 2009, 01:54 AM

Car looks awesome Luke. The drop gives it a perfect stance. Very nice.

Now just change the wheels and the rear spoiler and it will be perfect. JK

Seriously, the car looks amazing.

coolhandluke · July 6th, 2009, 11:03 AM

Originally Posted by 7upstang

Car looks awesome Luke. The drop gives it a perfect stance. Very nice.

Now just change the wheels and the rear spoiler and it will be perfect. JK

Seriously, the car looks amazing.

Thanks man.

The stance isn't 1/2 as good looking as your's though.

wveil3v · July 6th, 2009, 09:55 PM

Been thinkin about doin the roush rear springs and after seein yours I am going ahead with it. Do you guys think my little 2ton floorjack will jackup the pumpkin high enough to get the jackstands under the frame???

This is when I wished I had bought the next size up but didn't figure on doing any suspension work myself until seeing how easy the rear springs are from the writeup. .

Your's really looks fine, sure hope jack will work.

coolhandluke · July 6th, 2009, 10:39 PM

Originally Posted by wveil3v

Been thinkin about doin the roush rear springs and after seein yours I am going ahead with it. Do you guys think my little 2ton floorjack will jackup the pumpkin high enough to get the jackstands under the frame???

This is when I wished I had bought the next size up but didn't figure on doing any suspension work myself until seeing how easy the rear springs are from the writeup. .

Your's really looks fine, sure hope jack will work.

I actually used two floor jacks (Craftsman 2 1/4 ton) to pick up each side, supported the car with jack stands on the unibody rails, and used a transmission jack to lower and lift the rear end. Honestly, one floor jack probably won't be enough. I would at least use two and a set of jack stands (and wheels chalks). Better to borrow or buy a second one and prevent any possible problems.

I'm not sure that just one jack could get you to the right height anyway.

Good luck.

wveil3v · July 7th, 2009, 01:04 AM

Originally Posted by coolhandluke

I actually used two floor jacks (Craftsman 2 1/4 ton) to pick up each side, supported the car with jack stands on the unibody rails, and used a transmission jack to lower and lift the rear end. Honestly, one floor jack probably won't be enough. I would at least use two and a set of jack stands (and wheels chalks). Better to borrow or buy a second one and prevent any possible problems. I'm not sure that just one jack could get you to the right height anyway.

Good luck.

Hey thanks for getting back to me on the jack, saved me some time and trouble.

Mark

July 6th, 2009, 09:55 PM	#26
wveil3v Regular 2006 Mustang GT Join Date: Jul 2008 Location: NO. VA. Posts: 118	Been thinkin about doin the roush rear springs and after seein yours I am going ahead with it. Do you guys think my little 2ton floorjack will jackup the pumpkin high enough to get the jackstands under the frame??? This is when I wished I had bought the next size up but didn't figure on doing any suspension work myself until seeing how easy the rear springs are from the writeup. . Your's really looks fine, sure hope jack will work. __________________ 06 Windveil GT Auto - C&L racer intake/VMP perf tune, imco pro axelback, 18" chromies & more to come Last edited by wveil3v : July 6th, 2009 at 09:57 PM.

Threads Similar to: Roush Rear Leveling Springs Install
Thread	Thread Starter	Forum	Replies	Last Post
Part # on Roush Rear Springs?	coolhandluke	2005+	19	May 25th, 2009 08:49 PM
WTB Eibach Prokit REAR springs or H&R Sport rear springs	DSG04GT	Chassis/Suspension/Brakes	0	November 11th, 2008 07:46 AM
Supporting vendors with Roush rear springs?	5.0 Junkie	2005+	7	October 27th, 2008 08:02 PM
Supporting vendors with Roush rear springs?	5.0 Junkie	2005+	1	October 24th, 2008 06:58 PM
Roush Rear Springs	1LOUDGT	2005+	6	September 26th, 2007 04:10 AM

Sponsored Links	Remove Advertisements
Forums at Modded Mustangs Advertisement

July 6th, 2009, 12:43 AM	#23
hellbred07 Regular Join Date: Aug 2007 Posts: 353	Got mine on the way.

July 6th, 2009, 01:54 AM	#24
7upstang Newbie 2005 Redfire GT Join Date: Apr 2009 Location: Calgary Alberta Canada Posts: 38	Car looks awesome Luke. The drop gives it a perfect stance. Very nice. Now just change the wheels and the rear spoiler and it will be perfect. JK Seriously, the car looks amazing.

All times are GMT -4. The time now is 06:11 AM.
Contact Us - Modded Mustangs - Privacy Statement - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2009, Jelsoft Ent. Ltd. & SEO by vBSEO 3.1.0 ©2007, Crawlability, Inc.