Help Me Get Into the 13's

98SilverBullet · April 27th, 2007, 08:54 PM

I am planning out my mod list to get my slow ass npi into the 13's.

Current Mods:
UPR Offroad X
Pypes 2.5" Cat Back
CAI
Steada Tri-Ax's

Future Mods:
75mm TB
Plenum
4:10's

Will i break 13's with those mod's or is more stuff needed. Dont say Pi swap b/c i am doing that after summer.

HMUSN · April 27th, 2007, 08:57 PM

a nice 75 shot would help ya out

98SilverBullet · April 27th, 2007, 09:00 PM

I rather not do nitrous. For some reason it doesnt appeal to me.

burlingtonNC98GT · April 27th, 2007, 09:01 PM

instead of the throttle body and plenum, put in some pi cams. they're cheaper and they'll give u more hp.

HMUSN · April 27th, 2007, 09:09 PM

beef up your rear suspension and run drag radials. :wink

98SilverBullet · April 27th, 2007, 09:12 PM

any suggestions on suspension packages? Wouldnt mind dropping the car an inch or two. Also, would drag radials fit on the stock rims? I have RFT on the Svt's so i rather not change them out.

stanglifemike · April 27th, 2007, 11:37 PM

NO, I would say low 14's with all of those. Maybe 14.2

Casper98GT · April 28th, 2007, 10:26 AM

I am planning out my mod list to get my slow ass npi into the 13's.

Current Mods:
UPR Offroad X
Pypes 2.5" Cat Back
CAI
Steada Tri-Ax's

Future Mods:
75mm TB
Plenum
4:10's

I run a 13.8@99mph in my slow ass NPI. on DR's 14.0@99 without them.

I have

Cattless X-pipe, Mac catback.

BBK metal CAI, Steeda Underdrive pulleys, 3.73 gears, steeda tri-ax, Superchip chip, coil packs and wires. So yeah...i doubt 13's but deff low 14's. Depends on how you drive too, i would consier myself on the higher side of good.

I have PI intake, PI cams, BBK TB and plenum, Spec Stage 1 clutch, Upper nad lower C/A's now but no track times.

i also have a 75shot installed but never used. haha.

G.T. Rags · April 28th, 2007, 12:51 PM

How hard was it to do the pi cams swap casper?

ReverendDexter · April 28th, 2007, 12:58 PM

Originally Posted by 98SilverBullet

any suggestions on suspension packages? Wouldnt mind dropping the car an inch or two. Also, would drag radials fit on the stock rims? I have RFT on the Svt's so i rather not change them out.

Eibach, Maximum Motorsports, Griggs, Steeda, I think even Edelbrock is selling drag suspension kits these days.

April 27th, 2007, 08:54 PM	#1
98SilverBullet Regular Join Date: Apr 2007 Posts: 88 iTrader: 0 reviews	Help Me Get Into the 13's I am planning out my mod list to get my slow ass npi into the 13's. Current Mods: UPR Offroad X Pypes 2.5" Cat Back CAI Steada Tri-Ax's Future Mods: 75mm TB Plenum 4:10's Will i break 13's with those mod's or is more stuff needed. Dont say Pi swap b/c i am doing that after summer. __________________ '98 Mustang GT CAI, X-Pipe, Pypes Catback, Tri-Ax '96 Eclipse Gs-T Drop In K/N, T-2Gay @ 15psi, BSEK

April 27th, 2007, 08:57 PM	#2
HMUSN Doc 1986 SVO 48.47@ 12.58 Join Date: Nov 2006 Posts: 37,050 iTrader: 11 reviews	a nice 75 shot would help ya out __________________

April 27th, 2007, 09:00 PM	#3
98SilverBullet Regular Join Date: Apr 2007 Posts: 88 iTrader: 0 reviews	I rather not do nitrous. For some reason it doesnt appeal to me. __________________ '98 Mustang GT CAI, X-Pipe, Pypes Catback, Tri-Ax '96 Eclipse Gs-T Drop In K/N, T-2Gay @ 15psi, BSEK

April 27th, 2007, 09:01 PM	#4
burlingtonNC98GT Regular 1998 Mustang GT Join Date: Jan 2007 Location: Burlington, NC Posts: 217 iTrader: 0 reviews	instead of the throttle body and plenum, put in some pi cams. they're cheaper and they'll give u more hp. __________________ 1998 GT PI intake PI cams bbk cai flowmaster 40's catback bbk x-pipe w/ cats march pulleys RAM clutch Steeda Tri-axe

April 27th, 2007, 09:09 PM	#5
HMUSN Doc 1986 SVO 48.47@ 12.58 Join Date: Nov 2006 Posts: 37,050 iTrader: 11 reviews	beef up your rear suspension and run drag radials. :wink __________________

April 27th, 2007, 09:12 PM	#6
98SilverBullet Regular Join Date: Apr 2007 Posts: 88 iTrader: 0 reviews	any suggestions on suspension packages? Wouldnt mind dropping the car an inch or two. Also, would drag radials fit on the stock rims? I have RFT on the Svt's so i rather not change them out. __________________ '98 Mustang GT CAI, X-Pipe, Pypes Catback, Tri-Ax '96 Eclipse Gs-T Drop In K/N, T-2Gay @ 15psi, BSEK

April 27th, 2007, 11:37 PM	#7
stanglifemike IBEATU 06 GT, 98 GT, & 93 Notch Join Date: Dec 2006 Location: Douglasville, GA Posts: 5,937 iTrader: 0 reviews	NO, I would say low 14's with all of those. Maybe 14.2 __________________ 98 GT: some stuff 06 GT: more stuff 93 Notch: 4 cyl at birth, now 5.0 drivetrain and stock exterior and interior= True Sleeper Paxton/Vortech Crew Member #3 FRPP's #1 Dealer Injected Engineering BMR Suspension

Remove Advertisements Sponsored Links
Ford Mustang Forum Advertisement

Threads Similar to: Help Me Get Into the 13's
Thread	Thread Starter	Forum	Replies	Last Post
low 13's high 12's	VSR13	Drag	79	October 1st, 2008 03:29 AM
high 13's	GTSilver	99-04	5	August 24th, 2006 06:05 PM
Cheap ways to make a 96 mustang gt run mid to low 13's	mustang24	Drag	13	July 18th, 2006 07:42 PM

All times are GMT -4. The time now is 09:21 AM.
Contact Us - Modded Mustangs : Ford Mustang Forums - Privacy Statement - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2012, Jelsoft Ent. Ltd. & SEO by vBSEO 3.3.2 ©2009, Crawlability, Inc.