rpm gauge quit working

riceburnin03 · February 12th, 2008, 04:09 PM

my rpm gauge just quit working out of no where i put new gauges in two weeks ago and it worked fine i tuned it with my predator i got in the mail yesterday and it worked i went and turned off the rear o2 sensors un hooked the predator and started the car just now. and the needle does not move. does anyone know if it could of been the tuner that messed it up or what? any thought's on what this could be. i took off the tune and tryed it again and nothing then i loaded the tune back up and nothing any other suggestions

2kGT · February 12th, 2008, 04:14 PM

I had same problem with my reverse glow guages - needles would stick when it was cold outside, so I had to take the cluster back out and pull up on the needles just a bit so that they sit higher up off the guage cluster and will not stick to the new guage face.

riceburnin03 · February 13th, 2008, 01:09 PM

thanks that was the same problem with mine. i got it fixed now. it was a pain the ass to get the needle lined up perfact again.

February 12th, 2008, 04:09 PM	#1
riceburnin03 Regular 2003 mustang gt Join Date: Oct 2007 Location: j-ville nc Posts: 140	rpm gauge quit working my rpm gauge just quit working out of no where i put new gauges in two weeks ago and it worked fine i tuned it with my predator i got in the mail yesterday and it worked i went and turned off the rear o2 sensors un hooked the predator and started the car just now. and the needle does not move. does anyone know if it could of been the tuner that messed it up or what? any thought's on what this could be. i took off the tune and tryed it again and nothing then i loaded the tune back up and nothing any other suggestions __________________ bbk shorty headers,bbk o/r H, bbk udps, 75 tb&p tri ax shifter, flowmaster catback, k&n cai, diablosport tune (next 4.10s)

February 12th, 2008, 04:14 PM	#2
2kGT Regular Join Date: Oct 2007 Location: Upstate SC Posts: 447	I had same problem with my reverse glow guages - needles would stick when it was cold outside, so I had to take the cluster back out and pull up on the needles just a bit so that they sit higher up off the guage cluster and will not stick to the new guage face. __________________ Accufab 75mm tb & plenum MRT h-pipe Flowmaster catback FRPP king cobra clutch FRPP aluminum driveshaft FRPP 4.10 gear TA Perfromance girdle Steeda tri-ax shifter Moser 31 spline axles FRPP C Springs

February 13th, 2008, 01:09 PM	#3
riceburnin03 Regular 2003 mustang gt Join Date: Oct 2007 Location: j-ville nc Posts: 140	thanks that was the same problem with mine. i got it fixed now. it was a pain the ass to get the needle lined up perfact again. __________________ bbk shorty headers,bbk o/r H, bbk udps, 75 tb&p tri ax shifter, flowmaster catback, k&n cai, diablosport tune (next 4.10s)

Threads Similar to: rpm gauge quit working
Thread	Thread Starter	Forum	Replies	Last Post
I dont quit know what to say	thorpedo26	99-04	54	March 3rd, 2008 08:21 PM
High Beams quit working what do i do?	Pclacross	99-04	5	February 9th, 2007 08:10 PM
mileage gauge not working	new 5.0	Engine	3	January 17th, 2007 11:56 AM
speedometer quit working	blakemiester07	V6 Mustangs	7	December 24th, 2006 12:21 AM
Boost Gauge Not Working... Advice?	jerb43	Poweradders	7	September 20th, 2006 12:48 PM

All times are GMT -4. The time now is 02:32 AM.
Contact Us - Modded Mustangs - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2008, Jelsoft Ent. Ltd. & SEO by vBSEO 3.1.0 ©2007, Crawlability, Inc.