only half of my cluster works..

badf150boy123 · March 17th, 2008, 10:41 PM

only the right side works... so i got RPM.OIL.BATT.. where should i start??

04DSGV6 · March 17th, 2008, 10:51 PM

pull out cluster and check to see that both plugs are firmly connected. From there make sure that the wires leading to the connector aren't loose. Don't know much about the cluster but those are two possibilities

badf150boy123 · March 17th, 2008, 11:03 PM

its a 2000 gt.. how do i get it out?

04DSGV6 · March 18th, 2008, 06:54 PM

How to Install Mustang Gauge Inserts
here are instructions on how to get it out to put on gauge faces. Just follow all the instructions up to removing the lens.

Bullitt2445 · March 18th, 2008, 10:34 PM

Before you take the cluster apart, try this to see if it is a guage cluster problem or a computer problem. Press and hold the trip/odo button, and start the car. After a few seconds, you should see all of the guages sweep full right, then full left, then to normal. Release the trip button, and press and release again. The odo area should read "bulb", and all of the bulbs will light up. Several other presses will reveal diagnostic codes that a Ford Tech can use to troubleshoot your car. They really don't mean much without the proper conversion tables, so just ignore them. (One cool one is a digital tach, labeled "tac----" with the engine RPM as the dashes.) If the guages all sweep fine in the first part of the test, then your problem will be somewhere else. If they don't sweep, or only the ones that work now sweep, then dig in.

00redgt · March 19th, 2008, 10:43 PM

sounds like a loose connection,if i was the computer,wouldnt all the guages not work

emgjsdk1 · March 20th, 2008, 10:16 PM

i think its one of the wires in the back could be coming out or theres a short in one of them-just hope there isnt

March 17th, 2008, 10:41 PM	#1
badf150boy123 Regular 2000 mustang Gt 13.9 Join Date: Mar 2008 Location: INDY Posts: 73 iTrader: 0 reviews	only half of my cluster works.. only the right side works... so i got RPM.OIL.BATT.. where should i start??

March 18th, 2008, 10:34 PM	#5
Bullitt2445 Enthusiast 2012 GT Premium Join Date: Feb 2008 Location: Arkansas Posts: 722 iTrader: 0 reviews	Before you take the cluster apart, try this to see if it is a guage cluster problem or a computer problem. Press and hold the trip/odo button, and start the car. After a few seconds, you should see all of the guages sweep full right, then full left, then to normal. Release the trip button, and press and release again. The odo area should read "bulb", and all of the bulbs will light up. Several other presses will reveal diagnostic codes that a Ford Tech can use to troubleshoot your car. They really don't mean much without the proper conversion tables, so just ignore them. (One cool one is a digital tach, labeled "tac----" with the engine RPM as the dashes.) If the guages all sweep fine in the first part of the test, then your problem will be somewhere else. If they don't sweep, or only the ones that work now sweep, then dig in. __________________ Now I've gone and done it......

March 19th, 2008, 10:43 PM	#6
00redgt MM Fanatic 2000 mustang gt Join Date: Oct 2007 Location: vansant,va Posts: 4,092 iTrader: 5 reviews	sounds like a loose connection,if i was the computer,wouldnt all the guages not work __________________

March 20th, 2008, 10:16 PM	#7
emgjsdk1 Banned 2002 gt vert ? Join Date: Aug 2007 Location: SVA Posts: 808 iTrader: 0 reviews	i think its one of the wires in the back could be coming out or theres a short in one of them-just hope there isnt __________________ 2002 mustang gt vert. 18' bullitts k&n drop in air filter flowmaster mufflers soon to have mac off road x pipe and steeda udp pullies

Threads Similar to: only half of my cluster works..
Thread	Thread Starter	Forum	Replies	Last Post
Only half of my Cluster works???	badf150boy123	99-04	2	March 4th, 2008 11:17 AM
half dumped...	MikeD05GT	96-98	13	February 7th, 2008 08:39 AM
Half-pipe in a car	trev0006	The Clubhouse	9	October 20th, 2007 08:07 PM
Gauge Set up, Well half way!	MustangMatt96GT	Pictures	15	September 30th, 2007 03:08 AM
swapping '95 V6 gauge cluster to a '94-'98 GT cluster?	Alocatelli	V6 Mustangs	3	April 4th, 2007 02:38 PM

March 17th, 2008, 10:51 PM	#2
04DSGV6 Enthusiast 2004 Mustang V6 Join Date: Oct 2007 Location: Chicago,IL Posts: 546 iTrader: 1 reviews	pull out cluster and check to see that both plugs are firmly connected. From there make sure that the wires leading to the connector aren't loose. Don't know much about the cluster but those are two possibilities

March 17th, 2008, 11:03 PM	#3
badf150boy123 Regular 2000 mustang Gt 13.9 Join Date: Mar 2008 Location: INDY Posts: 73 iTrader: 0 reviews	its a 2000 gt.. how do i get it out?

March 18th, 2008, 06:54 PM	#4
04DSGV6 Enthusiast 2004 Mustang V6 Join Date: Oct 2007 Location: Chicago,IL Posts: 546 iTrader: 1 reviews	How to Install Mustang Gauge Inserts here are instructions on how to get it out to put on gauge faces. Just follow all the instructions up to removing the lens.

Remove Advertisements Sponsored Links
Ford Mustang Forum Advertisement

All times are GMT -4. The time now is 09:59 PM.
Contact Us - Modded Mustangs : Ford Mustang Forums - Privacy Statement - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2012, Jelsoft Ent. Ltd. & SEO by vBSEO 3.3.2 ©2009, Crawlability, Inc.