Voltage Amp???

My5point0Mustang · October 12th, 2005, 09:40 PM

Look, i got a problem, i just installed a hornet alarm system in my Mustang, i did it my self... everything workes great, besides two things, my trunk release does not release because there not enough power to trip it, the power the alarm system puts out is only 200 mA and the same with the fuel door, what can i do to up the voltage, is there something that i can buy that will send my power to whereever i need it when i hit that botton???

turp · October 12th, 2005, 10:57 PM

If it is only pulling 200 mA then your power loss is not in the alarm. I would check for a faulty ground/loose connector increasing the resistance through the circuit.

Jinxed · October 12th, 2005, 11:29 PM

alarms are NOT my speciality
but I would check what Slo said... if not that make sure you have it all wired correctly. Very ez to hook up the wrong wires.. and if that doesnt work, time to visit your local sterio shop

My5point0Mustang · October 13th, 2005, 12:12 AM

no, it says in the maunal that this wire will only put out 200 mA's its hooked up right, the alarm will not allow it to put out more than that... but i need to know if they make something that can send out more current, i mean that will take this 200mA and put more out instead

turp · October 13th, 2005, 01:58 AM

You could always add a step up transformer but they are fairly expensive I think. Maybe try a capacitor to give the voltage a quick boost to help actuate the solenoid operating those locks. I myself would think that a small capacitor would be the way to go unless you have to worry about surging voltage blowing fuses and what not. Then I would go with a small step up transformer for constant power output. I am just getting into auto electric so if their are any "old salts" that know something better feel free to join in and give a hand.

My5point0Mustang · October 20th, 2005, 12:16 PM

i figured out what i needed, and it was only 4-5 bucks i needed a relay, what the do is take power from the batterey and from the alarm and when the alarm sends its signal it opens the connection to the battery allowing 12 volts to pop the door open, and i got a little bit psyco with it and made it pop my gas door as well. hehe thanks

October 12th, 2005, 09:40 PM	#1
My5point0Mustang Regular Join Date: Oct 2005 Location: Chesapeake, Va Posts: 58	Voltage Amp??? Look, i got a problem, i just installed a hornet alarm system in my Mustang, i did it my self... everything workes great, besides two things, my trunk release does not release because there not enough power to trip it, the power the alarm system puts out is only 200 mA and the same with the fuel door, what can i do to up the voltage, is there something that i can buy that will send my power to whereever i need it when i hit that botton???

October 12th, 2005, 10:57 PM	#2
turp Moderator 1989 MUSTANG LX 5.0 16.17@86.21(bone stock on street tires) Join Date: Aug 2005 Location: Virginia Beach, VA Posts: 2,893	If it is only pulling 200 mA then your power loss is not in the alarm. I would check for a faulty ground/loose connector increasing the resistance through the circuit. __________________ SUPPORT YOUR LOCAL HOOKERS....HUG A TOW TRUCK DRIVER! Donate to lxhatch@gmail.com

October 12th, 2005, 11:29 PM	#3
Jinxed Regular Join Date: Aug 2005 Location: Joplin, MO Posts: 243	alarms are NOT my speciality but I would check what Slo said... if not that make sure you have it all wired correctly. Very ez to hook up the wrong wires.. and if that doesnt work, time to visit your local sterio shop __________________ http://www.shaunhamptondesign.com/Joe/Sigs/cool.jpg www.shaunhamptondesign.com

October 13th, 2005, 01:58 AM	#5
turp Moderator 1989 MUSTANG LX 5.0 16.17@86.21(bone stock on street tires) Join Date: Aug 2005 Location: Virginia Beach, VA Posts: 2,893	You could always add a step up transformer but they are fairly expensive I think. Maybe try a capacitor to give the voltage a quick boost to help actuate the solenoid operating those locks. I myself would think that a small capacitor would be the way to go unless you have to worry about surging voltage blowing fuses and what not. Then I would go with a small step up transformer for constant power output. I am just getting into auto electric so if their are any "old salts" that know something better feel free to join in and give a hand. __________________ SUPPORT YOUR LOCAL HOOKERS....HUG A TOW TRUCK DRIVER! Donate to lxhatch@gmail.com

Threads Similar to: Voltage Amp???
Thread	Thread Starter	Forum	Replies	Last Post
Voltage Problem	stang300a	V6 Mustangs	22	November 9th, 2007 02:44 PM
max MAF voltage	WAVEBYE	99-04	4	September 27th, 2007 07:54 PM
battery Voltage	new 5.0	94-95	3	June 19th, 2007 09:38 AM
voltage problem with my 91 stang	mysweetstang	5.0 Mustangs	8	August 16th, 2006 01:03 PM
voltage regulator..	espskillz	Classic Mustangs	3	August 7th, 2006 07:13 AM

October 13th, 2005, 12:12 AM	#4
My5point0Mustang Regular Join Date: Oct 2005 Location: Chesapeake, Va Posts: 58	no, it says in the maunal that this wire will only put out 200 mA's its hooked up right, the alarm will not allow it to put out more than that... but i need to know if they make something that can send out more current, i mean that will take this 200mA and put more out instead

October 20th, 2005, 12:16 PM	#6
My5point0Mustang Regular Join Date: Oct 2005 Location: Chesapeake, Va Posts: 58	i figured out what i needed, and it was only 4-5 bucks i needed a relay, what the do is take power from the batterey and from the alarm and when the alarm sends its signal it opens the connection to the battery allowing 12 volts to pop the door open, and i got a little bit psyco with it and made it pop my gas door as well. hehe thanks

All times are GMT -4. The time now is 02:23 AM.
Contact Us - Modded Mustangs - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2008, Jelsoft Ent. Ltd. & SEO by vBSEO 3.1.0 ©2007, Crawlability, Inc.