probe rotating assembly???

lilmarc1988 · May 6th, 2008, 01:38 AM

how are they? are they good quality? how much power would it support. im looking for 550 with supercharger and around 650 with nos. i would prolly just go with a built shortblock from mmr, because i would have to worry about anything. but any help would be a great help Stage 3 Motorsports 1996-08 Mustang GT 4.6L Forged Rotating Assembly - 10.5 Dished Pistons
also how much will this support and is there anything else i would need?? Stage 3 Motorsports 5.1 Modular Stroker Short Block

Kobra Killer · May 6th, 2008, 06:16 PM

The forged pistons, rods, & crank should be good up to about 800hp.
Be sure to balance with your flywheel/flexplate and harmonic balancer.
Use good quality rings like Sealed Power plasma-moly or similar.
Also make sure the valve train can handle the RPM you will be turning.

lilmarc1988 · May 6th, 2008, 11:29 PM

do you know the quality of the kit??? and is it a good compression for a turbo? o yea and is 373 good for a turbo because im getting 373 next week

Kobra Killer · May 11th, 2008, 01:29 AM

Probe stuff is pretty good quality and forging makes thing tougher.
Depending on pressure, a turbo will raise CR 1-2 points.
At 9.3 with stock heads that's 11.3:1.
That should run on 91 octane pump gas but watch for pinging.

tom2000r · May 11th, 2008, 02:14 AM

o ring heads, or block deck, and use head studs...use correct heat range spark plugs...

lilmarc1988 · May 12th, 2008, 10:40 PM

so how is it a high compresion ratio with stock heads??? that kit wont get my cr to like 8.5-9?

lilmarc1988 · May 12th, 2008, 10:45 PM

Stage 3 Motorsports 1996-08 Mustang GT 4.6L Forged Rotating Assembly - 18.1 Dished Pistons
is this something i would need???

Hillsbaseball08 · May 14th, 2008, 08:08 PM

I'm also looking at this. I want to run a supercharger with my nitrous, are forged internals all I need?

May 6th, 2008, 01:38 AM	#1
lilmarc1988 Hardcore Enthusiast 2001 mustang gt Join Date: Sep 2007 Location: lehigh acres, fl Posts: 1,006	probe rotating assembly??? how are they? are they good quality? how much power would it support. im looking for 550 with supercharger and around 650 with nos. i would prolly just go with a built shortblock from mmr, because i would have to worry about anything. but any help would be a great help Stage 3 Motorsports 1996-08 Mustang GT 4.6L Forged Rotating Assembly - 10.5 Dished Pistons also how much will this support and is there anything else i would need?? Stage 3 Motorsports 5.1 Modular Stroker Short Block __________________ mods: tb and plenum, cold air intake, ebaich lowering kit, flow weld in, custom o/r x, RAM HDX Clutch, Vortech V1 S Trim(not installed), and unknown chip. Start the quest for low 11's high 10's http://www.cardomain.com/ride/3112249

May 6th, 2008, 06:16 PM	#2
Kobra Killer Regular Join Date: Sep 2006 Location: Arvada, CO Posts: 66	The forged pistons, rods, & crank should be good up to about 800hp. Be sure to balance with your flywheel/flexplate and harmonic balancer. Use good quality rings like Sealed Power plasma-moly or similar. Also make sure the valve train can handle the RPM you will be turning. __________________ Clevelands Rule https://home.comcast.net/~jimmiephil...er_project.htm

May 6th, 2008, 11:29 PM	#3
lilmarc1988 Hardcore Enthusiast 2001 mustang gt Join Date: Sep 2007 Location: lehigh acres, fl Posts: 1,006	do you know the quality of the kit??? and is it a good compression for a turbo? o yea and is 373 good for a turbo because im getting 373 next week __________________ mods: tb and plenum, cold air intake, ebaich lowering kit, flow weld in, custom o/r x, RAM HDX Clutch, Vortech V1 S Trim(not installed), and unknown chip. Start the quest for low 11's high 10's http://www.cardomain.com/ride/3112249

May 11th, 2008, 01:29 AM	#4
Kobra Killer Regular Join Date: Sep 2006 Location: Arvada, CO Posts: 66	Probe stuff is pretty good quality and forging makes thing tougher. Depending on pressure, a turbo will raise CR 1-2 points. At 9.3 with stock heads that's 11.3:1. That should run on 91 octane pump gas but watch for pinging. __________________ Clevelands Rule https://home.comcast.net/~jimmiephil...er_project.htm

May 12th, 2008, 10:40 PM	#6
lilmarc1988 Hardcore Enthusiast 2001 mustang gt Join Date: Sep 2007 Location: lehigh acres, fl Posts: 1,006	so how is it a high compresion ratio with stock heads??? that kit wont get my cr to like 8.5-9? __________________ mods: tb and plenum, cold air intake, ebaich lowering kit, flow weld in, custom o/r x, RAM HDX Clutch, Vortech V1 S Trim(not installed), and unknown chip. Start the quest for low 11's high 10's http://www.cardomain.com/ride/3112249

May 11th, 2008, 02:14 AM	#5
tom2000r Enthusiast Join Date: Jan 2008 Location: ohio Posts: 753	o ring heads, or block deck, and use head studs...use correct heat range spark plugs...

May 12th, 2008, 10:45 PM	#7
lilmarc1988 Hardcore Enthusiast 2001 mustang gt Join Date: Sep 2007 Location: lehigh acres, fl Posts: 1,006	Stage 3 Motorsports 1996-08 Mustang GT 4.6L Forged Rotating Assembly - 18.1 Dished Pistons is this something i would need??? __________________ mods: tb and plenum, cold air intake, ebaich lowering kit, flow weld in, custom o/r x, RAM HDX Clutch, Vortech V1 S Trim(not installed), and unknown chip. Start the quest for low 11's high 10's http://www.cardomain.com/ride/3112249

May 14th, 2008, 08:08 PM	#8
Hillsbaseball08 Regular 2002 Mustang GT 8.15@86 (1/8) Join Date: Oct 2007 Location: Fort Worth,Texas Posts: 406	I'm also looking at this. I want to run a supercharger with my nitrous, are forged internals all I need? __________________ 07 GT500 & 2002 GT: 100 Shot Of Nitrous, 75mm BBK Throttle Body and Plenum, C&L Intake, Flowmaster Exaust, Bassani X Pipes, 3:73 Gear Ratio, BBK Upper and Lower Control Arms, Pro 5.0 Shifter, DiabloSport Tune, Underdrive Pulleys, Line Lock.

Threads Similar to: probe rotating assembly???
Thread	Thread Starter	Forum	Replies	Last Post
For Sale: Comp solid roller lifters, TFS Rockers, Probe rotating assembly	Darrell	Engine	1	April 22nd, 2008 03:17 AM
Rotating Assembly?	lethal2v	96-98	36	January 31st, 2008 05:15 PM
Rotating Assembly	J Mac0123	99-04	13	October 3rd, 2007 01:07 PM
Rotating Assembly on an 03' GT	hubba076	99-04	1	May 16th, 2007 02:34 AM
FS: Rotating Assembly w/other items	68 dlxcoupe	For Sale	0	September 12th, 2006 01:22 PM

All times are GMT -4. The time now is 08:21 PM.
Contact Us - Modded Mustangs - Top
Modded Mustangs is ©2005-2008, All Rights Reserved, And is Not Affiliated with Ford Motor Company. Forum is powered by vBulletin ©2000 - 2008, Jelsoft Ent. Ltd. & SEO by vBSEO 3.1.0 ©2007, Crawlability, Inc.