[justinsstang]

N/A ICT8 (itschristorres8)Engine---- $3500 ---------@ 240rwhp
99-04 Split Port Intake Swap- -------$800 -----+40 @ 280rwhp
SCT X-Cal 2 Tuner (VMP)---------- $400 -----+10 @ 290rwhp
98 Mustang GT 8.8in Rear End------ $400 -------------+Trac
4.10 Rear End Gears -----------------$700------------ -.5 1/4mi. EST Time.
Mac Long Tube Headers------------- $400 -----+20 @ 310rwhp
Nitrous 125 Shot--------------------- $500 -------------(Power Adder) +125hp

---------------------------------------$6700 ---------@ 310rwhp N/A (no PA)
------------------------------------------------------------------------------------@ 435rwhp N/A (With PA)

CUTE?
I need to get the Split Port swap first though.. pretty pointless to send him my engine and have him port my single when im gonna replace w/ a split

[whitemustang02]

Originally Posted by justinsstang N/A ICT8 (itschristorres8)Engine---- $3500 ---------@ 240rwhp 99-04 Split Port Intake Swap- -------$800 -----+40 @ 280rwhp SCT X-Cal 2 Tuner (VMP)---------- $400 -----+10 @ 290rwhp 98 Mustang GT 8.8in Rear End------ $400 -------------+Trac 4.10 Rear End Gears -----------------$700------------ -.5 1/4mi. EST Time. Mac Long Tube Headers------------- $400 -----+20 @ 310rwhp Nitrous 125 Shot--------------------- $500 -------------(Power Adder) +125hp ---------------------------------------$6700 ---------@ 310rwhp N/A (no PA) ------------------------------------------------------------------------------------@ 435rwhp N/A (With PA) CUTE? I need to get the Split Port swap first though.. pretty pointless to send him my engine and have him port my single when im gonna replace w/ a split

ur rwhp # r way off unless u get high cr pistons a grate cam, heads, intake, and a grate dyno tune , u will not be seing 290hp to the wheels n/a that has yet to be done.

also ur final goal of 310rwhp n/a is rediculaus i think i have a shot at brakeing the 300 mark with the set up i am planing but that is because i am gana be pushing the cr ratio higher then any one has, and will need to be runing on 100+ octane not somthing you are gana want to be runing on the street very often.

[ESG-642T]

This is so wrong.

[ESG-642T]

Originally Posted by justinsstang N/A ICT8 (itschristorres8)Engine---- $3500 ---------@ 240rwhp 99-04 Split Port Intake Swap- -------$800 -----+40 @ 280rwhp SCT X-Cal 2 Tuner (VMP)---------- $400 -----+10 @ 290rwhp 98 Mustang GT 8.8in Rear End------ $400 -------------+Trac 4.10 Rear End Gears -----------------$700------------ -.5 1/4mi. EST Time. Mac Long Tube Headers------------- $400 -----+20 @ 310rwhp Nitrous 125 Shot--------------------- $500 -------------(Power Adder) +125hp ---------------------------------------$6700 ---------@ 310rwhp N/A (no PA) ------------------------------------------------------------------------------------@ 435rwhp N/A (With PA) CUTE? I need to get the Split Port swap first though.. pretty pointless to send him my engine and have him port my single when im gonna replace w/ a split

If chris is gonna built you an engine, and it's gonnabe split port then 230-240rwhp is what your gonna get with full bolt ons. If its not split port then 210-220hp.

Then add the 125shot to that (probably about 100-115realastic hp)

[shadow5403]

SSMs crate engine puts out up to 390 NA at the crank which is prolly 345ish at the wheels.....so his numbers nay not be accurate....but hittin over 300 rwhp NA is possible.

[ESG-642T]

Originally Posted by shadow5403 SSMs crate engine puts out up to 390 NA at the crank which is prolly 345ish at the wheels.....so his numbers nay not be accurate....but hittin over 300 rwhp NA is possible.

No its not. Nobody has made 300rwhp N/A yet. Sorry...

[shadow5403]

hey im just readin off SSMs website...dont shoot the messenger. those numbers are prolly for a stage 3 motor with a huge cam only meant for racing tho.

[whitemustang02]

no no one has done it at all incloding the ssms fox it has the record at 278 rwhp

[Hourofpain]

stroke it enough and run it off race fuel its possible

[Avaric3]

Originally Posted by Hourofpain stroke it enough and run it off race fuel its possible

were talking pump gas (93 octane) tho, the record is ssms which i guess is 278rwhp like 02 said.

i think more is obtainable tho if you go all out w/ different heads, cam and intakes. i believe they use the satge 3 stuff on their car so if you were to use, say the ssx sheet metal upper and the rpm lower w/ imrcs removed and the rpm heads, i bet you could squeeze about 285-290rwhp out of it

[itschristorres8]

Originally Posted by shadow5403 hey im just readin off SSMs website...dont shoot the messenger. those numbers are prolly for a stage 3 motor with a huge cam only meant for racing tho.

show the page cause im 100% sure its 260rwhp


btw for those wondering why his motor is cheaper then your qoute may be is because his is VERY budget built
consist of forged rods. pistons, new bearings, rings and just an upgraded valve terrain

[Onemanzu]

Originally Posted by justinsstang N/A ICT8 (itschristorres8)Engine---- $3500 ---------@ 240rwhp 99-04 Split Port Intake Swap- -------$800 -----+10 @ 250rwhp SCT X-Cal 2 Tuner (VMP)---------- $400 -----+10 @ 260rwhp 98 Mustang GT 8.8in Rear End------ $400 -------------+Trac 4.10 Rear End Gears -----------------$700------------ -.5 1/4mi. EST Time. Mac Long Tube Headers------------- $400 -----+20 @ 280rwhp Nitrous 125 Shot--------------------- $500 -------------(Power Adder) +125hp ---------------------------------------$6700 ---------@ 310rwhp N/A (no PA) ------------------------------------------------------------------------------------@ 435rwhp N/A (With PA)

Like they said you will need to raise your compression ratio... cam and tune it for nitrous you might be able to see 300+ but it will take more work and money then your thinking

Plus you will have to add in labor unless you think you can do it all yourself

[ESG-642T]

Originally Posted by Onemanzu Like they said you will need to raise your compression ratio... cam and tune it for nitrous you might be able to see 300+ but it will take more work and money then your thinking Plus you will have to add in labor unless you think you can do it all yourself

300hp n/a won't happen for a while.
But It'll happen.....

[itschristorres8]

not to mention i NEVER qouted 240rwhp with a single port all motor and $3500 built
honestly this thread is making drawing me away from doing this motor
not to mention by the time this motor is ready to be built i will not be building motors in this fashion
maybe a budget build will be cheaper but not re-using old parts

[whitemustang02]

Originally Posted by SSStang 300hp n/a won't happen for a while. But It'll happen.....

I’d say it will be done in about 2 years. A little more stroke and upped cr and it will be there. I am planning on doing this, stroking the block to the limits and going up to 12-13 cr and a all the supporting modes (i.e. good heads, intake, ect.) and I should be over 300+

[itschristorres8]

you'll need race gas
pump gas will NOT support that power
and we cant get much more stroke without clearance issues

[whitemustang02]

Originally Posted by itschristorres8 you'll need race gas pump gas will NOT support that power and we cant get much more stroke without clearance issues

Oh I know pump gas is out at that point, but it is going to be sitting in an open track race car. So higher octane is something I will be willing to sacrifice for power.

Also what is the clearance issue, I haven’t done a tone of research on this yet, but I know I there is a tt super cope drag car, and it is stroked out to 4.7L but not sure what they did to get that.

[ESG-642T]

Originally Posted by whitemustang02 Oh I know pump gas is out at that point, but it is going to be sitting in an open track race car. So higher octane is something I will be willing to sacrifice for power. Also what is the clearance issue, I haven’t done a tone of research on this yet, but I know I there is a tt super cope drag car, and it is stroked out to 4.7L but not sure what they did to get that.

5,000$ block...
We're working on it.

[itschristorres8]

maybe a 4.5L block that isnt the based 3.8L block

[itschristorres8]

Originally Posted by SSStang 5,000$ block... We're working on it.

the aluminum block lol thats different
that'll make 300rwhp for sure
4inch bores
but its pretty damm hard to come up with 25 people that wana pay $5k for a BLOCK alone