|Topic Review (Newest First)|
|March 27th, 2019 07:32 PM|
|March 26th, 2019 09:39 PM|
|SSG Pate||Your getting closer man.|
|March 26th, 2019 11:16 AM|
|Sonic 02||So had the car on dyno yesterday dialed in AFR and set idle and start fuel. We tuned part throttle then did a couple pulls. Had a couple issues first being the valve gaskets leaked. It didnt leak during the heat cycles but should be easy fix. The second being the car would only make 6 # of boost. So will have to go back and check for exhaust and boost leaks. Bright side from the pull it's going to have some potentia once the boost problem is fixed.|
|March 17th, 2019 05:35 PM|
You gotta watch that lead based Race gas it will make short work of your wideband sensors and your 02 sensors. It is hit or miss on how fast it happens
|March 17th, 2019 08:38 AM|
|March 16th, 2019 09:00 PM|
|March 16th, 2019 12:36 PM|
|Sonic 02||Just a little update. Dropped the car at the tuner yesterday. I have a Monday appointment but he said he is a little behind yesterday when I dropped it off. So might not get it on rollers until Tuesday|
|January 23rd, 2019 07:51 PM|
Got the front bumper cover on today and the hood. It has been 4 years since the hood has been on. Also got the upper radiator support trimmed up and shaped.
20190123_162404 by kevin faria, on Flickr
20190123_162548 by kevin faria, on Flickr
20190123_162413 by kevin faria, on Flickr
Here are the upper radiator mounts I modified to hold radiator
20181107_153853 by kevin faria, on Flickr
20181107_153857 by kevin faria, on Flickr
|January 21st, 2019 07:11 PM|
|Sonic 02||Just a little update I have been battling a lean reading on my wide band. I thought my o2 sensor on WB was bad. . I finally found the problem. I bought my Victor Jr used and previous own had drilled and tapped the intake to add a vacuum port. It was hidden under the 6061 elbow and I thought the sound I was hearing was normal TB noise. The weather has not been cooperating with getting the car to the tuners. I'm hoping to get it there before end of the week if I don't it will be March before I can take it.|
|December 21st, 2018 06:57 PM|
We got 2''' of rain last night and today so dyno appointment has to be rescheduled to the first of the year. Fabricator finally got the top radiator support to me today so worked on final fitting so it wasn't a complete wasted day off.
Wiring on transmission completed and transbreak tested . The relay pack for transmission looks a little intimidating but it was pretty straight forward. Also I fabricated a new front bumper support. I was going to buy tubular but made my own for about 10 bucks also made a bracket that mounts to stock steering wheel to hold the transbreak and line lock buttons.
|November 23rd, 2018 09:29 PM|
Got the exhaust finished so it's now coming out mufflers. Had quite a battle with abs delete .Dorman must have had a bad run on their T's. Ended up switching to npt T's to solve leaking problems. Plumbed the wastegate and boost controller up. Sent drawing over to have upper radiator support fabricated should get it on Monday Got transbreak button and the momentary switches in. So next week I'm going to try and get transmission wired up, and upper radiator support finished.
I made dyno appointment for December 21
|October 25th, 2018 04:23 PM|
|October 24th, 2018 10:45 PM|
|October 24th, 2018 07:01 PM|
|Sonic 02||So after 3 tees I finally found one that wasn't defective. Before any questions if it was really the tees. I never had to remake the flares to get it to stop leaking. The problem I have now is even though I'm getting no bubbles out of the bleeder and good flow of brake fluid out of the bleeders the pedal still goes to the floor. Just wondering if anyone has had the trouble getting their brakes right after abs delete|
|October 20th, 2018 03:22 PM|
Sounding Solid Man thanks for posting up that video I have been wondering what has happened to you lately.
I too couldnt fit anything other then a 3" piping through my K member
|October 20th, 2018 12:38 PM|
|Sonic 02||I had to reduece the 4 inch downpipe to 3 inches to get it through the kmember. I have it all tacked up just have 1 more weld then exhaust is done . I also installed super high flow cat to pass visual inspection. Finished all the brake lines but found out I have a defective T that won't stop leaking. Line lock is wired up just needs to be powered. The hobbs switches are mounted and tested. This project is winding down. The to main things to be done is plumb up boost reference for wastegate and wire up FB transmission controller. When that's done tuner will come and pick it up then it off for 93 octane tune and race gas tunes|
|September 15th, 2018 10:36 AM|
After 4 long years finally first start up. Idling at 1k and running lean but my tuner sent me a couple tunes. Still have a lot of beautification to do but major step forward.
Next is finish the flare for rear breaks, wire up freddy brown lockup controller and transbrake, getting down pipe to mid pipe done and fabricating a new top for radiator support
|September 8th, 2018 04:43 PM|
Got the new intercooler brackets fabricated. The cold side welded up. Just have to redo the intercooler to throttle body pipe. I got the moroso 3 inch wheel studs installed on the front. I was having trouble getting them in so had to to remove the hubs and press them in on a press
Rotors look a little rusty but it's just from car sitting for 4 years
This week I'm going to flare rear break lines and . Fix the throttle body to intercooler piping. Moving intercooler threw
Angles off. Down pipe is going to need a lot modification if I can get all done it will be time for start up
|September 1st, 2018 11:29 AM|
|August 31st, 2018 10:50 PM|
|SSG Pate||you could make your own coolant over flow tank like i did.|
|This thread has more than 20 replies. Click here to review the whole thread.|