Forums at Modded Mustangs - Reply to Topic
Thread: From Vortech to Turbo Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Forums at Modded Mustangs forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
September 30th, 2019 10:26 PM
WickedSnake00 That leaves pretty damn good in that case. Pretty encouraging to see someone with a manual and sock ECU leaving like that. I'll have to turn on the two step, get some slicks and see what she'll do.
September 30th, 2019 10:13 PM
98SnakeHorse
Quote:
Originally Posted by WickedSnake00 View Post
Looks like you have the launch pretty well figured out. What's your setup for it? Still a stock ECU stick car? What rear gear?


Stock ecu. 6spd with a 3.73. Mostly teamz suspension stuff. Upper and lowers with their anti roll bar


Sent from my iPhone using Tapatalk
September 30th, 2019 09:52 PM
WickedSnake00 Looks like you have the launch pretty well figured out. What's your setup for it? Still a stock ECU stick car? What rear gear?
September 30th, 2019 12:09 PM
98SnakeHorse

August 14th, 2019 10:08 AM
98SnakeHorse https://youtu.be/fBm05YJXHMk

6.5 @ 108pm 1.49 60ft (1/8th)
July 30th, 2019 12:15 PM
98SnakeHorse Ran my quickest pass this past weekend. 6.64 @ 107mph.

July 19th, 2019 02:52 PM
lowboost2v Good looking build. Keep it up.
July 15th, 2019 06:28 PM
98SnakeHorse The car is a ripper and a blast to drive.

May 20th, 2019 02:43 PM
98SnakeHorse
Quote:
Originally Posted by y2k02 View Post
I dont believe the cams are your issue. How much hp and how high do you want to spin your engine. 228 is a baby cam. For sure 100lbs of seat pressure that your valve springs have is just not enough. You need 130lbs of seat pressure!
Interesting, I will for sure upgrade the springs when I swap out the cams. I would have been happy with 650ish whp. Spun the car to 7k last year and it liked it. Not so much this year.
May 14th, 2019 10:28 PM
y2k02 I dont believe the cams are your issue. How much hp and how high do you want to spin your engine. 228 is a baby cam. For sure 100lbs of seat pressure that your valve springs have is just not enough. You need 130lbs of seat pressure!
May 13th, 2019 01:21 PM
98SnakeHorse
Quote:
Originally Posted by y2k02 View Post
What are your cam specs? What valve springs are you running. Looks more like something else is making the hp drop than the cams.

CMS 2.5 blower cams
Cam specs: 536/.540 lift, 228/235 .050 duration, 114 LSA

CMS Stg 2 Springs .600" lift

Spring load at 1.68" 100lbs
Spring load at 1.040" 270lbs
Spring rate 275 lbs per inch
Coil bind 1.020"
May 10th, 2019 10:55 AM
y2k02 What are your cam specs? What valve springs are you running. Looks more like something else is making the hp drop than the cams.
May 7th, 2019 03:05 PM
98SnakeHorse
April 24th, 2019 01:41 PM
98SnakeHorse Dyno is complete.... Blower cams hurt me, and I was getting close to pegging my maf. Am also in need of a larger downpipe. Mine is just a 3"

Final#s are 574rwhp and 563rwtq. 15psi with 15 degrees of timing. Boost would begin to drop above 6200 rpm and power would completely fall off. My own fault for not switching out the cams. The old owner of Modular Powerhouse actually walked in right as we were finishing up and mentioned that my stock cams would have probably made more power. Anyway... power is still up and at way lower rpms as it was last year. I think I can get close to a 9sec pass on this setup. But we will see. Over 120ftlb more tq!

Last years Graph


This years Graph



April 10th, 2019 01:52 PM
98SnakeHorse
Quote:
Originally Posted by MineralGreyGT View Post
Looks great, what k member you running?

Sent from my LG-H932 using Tapatalk
Thanks, its a UPR k-member
April 10th, 2019 11:42 AM
MineralGreyGT Looks great, what k member you running?

Sent from my LG-H932 using Tapatalk
April 10th, 2019 11:37 AM
98SnakeHorse Car is getting all buttoned up and heading to the Dyno on Sat. I'll post some vids and power #'s after that.





April 3rd, 2019 11:02 AM
98SnakeHorse
Quote:
Originally Posted by MineralGreyGT View Post
Very interested to see how the Dyno graph compares before and after, also where did you get that center console delete panel?

Sent from my LG-H932 using Tapatalk
Oh for sure me too.. I made that panel out of some scrap aluminum
April 3rd, 2019 10:40 AM
MineralGreyGT Very interested to see how the Dyno graph compares before and after, also where did you get that center console delete panel?

Sent from my LG-H932 using Tapatalk
April 3rd, 2019 10:31 AM
5rand0n7 I subscribed to your channel for some future entertainment
This thread has more than 20 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome