Forums at Modded Mustangs - Reply to Topic
Thread: is the ACT SENSOR IMPORTANT ENOUGH TO LEAVE OFF? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Forums at Modded Mustangs forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
March 12th, 2007 05:31 PM
sb2f5marine69 straight out of the ford manual
March 12th, 2007 05:31 PM
sb2f5marine69 The act snsor :This measures the temperature of the air entering the engine. Which impacts the fuel ratio; the cooler the incoming air is the denser it is. Denser air can utilize more fuel, giving us even greater accuracy in obtaining our desired air to fuel ratio.
March 12th, 2007 04:03 PM
TENGRAM the wires should come from the injector harness. scope it out and see if you can find them. if not you could run a new signal wire from pin 25 at the ECM to the ACT and hook the black wire (SigRTN) to either the ECTs black wire or run it straight to pin 46 at the ECM. check this diagram (ACT= IAT or Intake Air Temp Sensor):
March 12th, 2007 03:10 PM
vicma762004 ok thnx guys so in other words locate it and replace it right?

my problem is that the plug id on the intake tube but the wire going out to the computer of where ever it goes is M.I.A
how would i go by rplacing it?
March 12th, 2007 06:01 AM
Bill it measures the temp. of the air entering. and it does have an impact on the A/F ratio. sends the temps of the air to the Computer
i was having problems in my 92 5.0 cause mine went bad. but in my 92 its not on the air tube. its in the lower intake.
March 12th, 2007 03:46 AM
sb2f5marine69 yes but it uses that in coming air as well to help determin air fuel ratio. also look in a haynes manual for a break down
March 12th, 2007 12:29 AM
Zak Oh sorry.. you did mentioned it was idling & running roughly.

sb2f5marine69: are you sure about the a/f ratio? usually, it's the MAF sensor that adjusts AFR.. ACT is in charge of controlling ignition timing according to air density which is affected by temperature. This is why it is relocated to the pressure side in forced induction applications as compressed air rises in temperature therefore requires some retard accordingly. I think.
March 11th, 2007 09:08 PM
sb2f5marine69 yep it will have a bad a/f ratio
March 11th, 2007 06:46 PM
Zak Bad ignition timing is what you get with a faulty or missing ACT sensor.. maybe the EEC was depending on the TPS, MAF & water temperature sensors to do the guess work as mentioned. It's strange if your idle behavior wasn't noticeable.
March 11th, 2007 04:41 PM
TENGRAM without the ACT the ECM will use other sensors to "guess" at what temp the air is. the engine will not run optimally w/o the ACT. get one and hook it up. my2cents
March 11th, 2007 02:59 PM
vicma762004
is the ACT SENSOR IMPORTANT ENOUGH TO LEAVE OFF?

what happens if the air charge sensor is not connected. when i bought my car it came unplugged and really dont know where the wire going out is. the plug is on the air tube but the conection going out is nowhere to be found. my car ever since i bought it has been running rough, idling rough, misfiring. the car is running better after changing fuel,air filter, plugs, plug wires, cleaned maf and throttle body.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome