Forums at Modded Mustangs - Reply to Topic
Thread: Percy header gaskets Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Forums at Modded Mustangs forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
April 15th, 2011 07:29 PM
Ultrakla$$ic Percy Seal-4-Good FTW!!!!!!!!!!!!!!! I used them with my Full exhaust install and no leaks whatsoever. I wouldn't use anything else from now on.
April 15th, 2011 02:54 PM
BlueDevil
Quote:
Originally Posted by eleanor08 View Post
Im guessing you found the instructions on the Percy site? Ill go look for them. So BlueDevil, what did you think of the gaskets? And nice ride BTW.
I found the instructions on the packaging...which was a while back so I can't remember... I do like the gaskets. The paper ones that came with my headers leaked almost immediately.
Thanks for the compliment, and good luck to you!
April 14th, 2011 10:05 PM
Darwin
Quote:
Originally Posted by Ace417 View Post
i havent noticed.
Me2, Like he said!
April 14th, 2011 08:49 PM
Ace417
Quote:
Originally Posted by saleen_s331 View Post
do they leak??
i havent noticed.
April 14th, 2011 08:33 PM
eleanor08
Quote:
Originally Posted by BlueDevil View Post
I have the percy's dead soft aluminum gaskets. The instructions tell you which way they face.
Im guessing you found the instructions on the Percy site? Ill go look for them. So BlueDevil, what did you think of the gaskets? And nice ride BTW.
April 14th, 2011 07:53 PM
saleen_s331
Quote:
Originally Posted by Ace417 View Post
i used the stock gaskets
do they leak??
April 14th, 2011 06:26 PM
Ace417 i used the stock gaskets
April 14th, 2011 04:50 PM
BlueDevil I have the percy's dead soft aluminum gaskets. The instructions tell you which way they face.
April 14th, 2011 04:25 PM
saleen_s331
Quote:
Originally Posted by Emay View Post
Saleen - loosen the motor mounts at the k-member and slightly slide the motor over just a touch and that rub will be gone. Done it several times for guys locally. Mounts are slotted for this very reason.
Perfect... I will do that as soon as I pull into the shop when I put the cams in!! Thank you again +1 for you!! I was getting pretty tired of it!
April 14th, 2011 03:43 PM
eleanor08
Quote:
Originally Posted by Emay View Post
Saleen - loosen the motor mounts at the k-member and slightly slide the motor over just a touch and that rub will be gone. Done it several times for guys locally. Mounts are slotted for this very reason.
Thank you for the heads up!!!!

rep+1
April 14th, 2011 03:21 PM
Emay Saleen - loosen the motor mounts at the k-member and slightly slide the motor over just a touch and that rub will be gone. Done it several times for guys locally. Mounts are slotted for this very reason.
April 14th, 2011 02:38 PM
saleen_s331 This is a post i put up in another thread about the install:

The install took me and my buddy about 4 hours... that was including removing several parts that we later deemed unnecessary to remove. you do however have to lift the motor about 1 inch and remove several things to squeeze the LTs in there, If you have a hydraulic lift make sure you lift the motor from the bottom rather than pulling it from the top, hence removing the unnecessary parts! I DO NOT RECOMMEND DOING THIS IN YOUR GARAGE!! haha i know people do it all the time but they claim it takes sometimes up to 10-11 hours, entirely too long if you ask me.

The only downside to the longtubes is that they rub on the right inner fenderwell just barely but upon making a left hand turn and getting on the throttle the motor torques right and the body rolls left so it rubs slightly, which is quite gay. But the sound and power is badass...
April 14th, 2011 02:35 PM
Silverrider well i am going to say i have never used them before but i am jealous of your new set up! have to let me know how you like that set up when it is complete, was thinking of a similar set up! Thanks!
April 14th, 2011 02:01 PM
eleanor08 Do you like it??? How did it go?? any chance we can get a video of the sound??
April 14th, 2011 01:55 PM
saleen_s331 Mac, with a Prochamber...
April 14th, 2011 01:53 PM
eleanor08 LMAO.... Im going to trust ya on this one!!!!

I was asking because I have never used aluminum gaskets before..

What brand of LTH's did you just install?
April 14th, 2011 01:50 PM
saleen_s331
Quote:
Originally Posted by eleanor08 View Post
The gaskets that came, said on the top of the package that they where made by Percy for Kook's... LOL.. So I don't know, here is a link to the gaskets.

Seal-4-Good - Header Flange Gaskets - Ford - Percy's High Performance - Online Store

They are called Seal 4 Good...
Well... after several minutes of deep concentrated thought I have come to the conclusion, with a name like "Seal-4-Good" they have to be good...
April 14th, 2011 01:43 PM
eleanor08 The gaskets that came, said on the top of the package that they where made by Percy for Kook's... LOL.. So I don't know, here is a link to the gaskets.

Seal-4-Good - Header Flange Gaskets - Ford - Percy's High Performance - Online Store

They are called Seal 4 Good...
April 14th, 2011 01:27 PM
saleen_s331 thats kind of odd.. I ordered the exact setup and they sent me the other gaskets...
April 14th, 2011 01:22 PM
eleanor08 MAC's, and a pro chamber.
This thread has more than 20 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome