|Topic Review (Newest First)|
|August 14th, 2019 11:46 PM|
I just did the same swap with my 2006 gt. My wheel control lights up when the lights are on.
I seen to have all the issues with my install though. My media controls shows different resistance values for each media button but my PAC swi-rc doesn't detect the entry via purple wire from the wheel to the white wire of the PAC. My cruise control just doesn't work when I tested it on the highway going 60mph.
My wheel version doesn't have the SYNC button or the phone button.
|March 11th, 2019 02:59 PM|
Originally Posted by oddwolf248 View Post
|February 19th, 2019 05:51 PM|
|December 27th, 2018 04:14 PM|
Hi ! First mod on my Mustang ! Can somebody help me ? I am doing the Shelby GT500 wheel in a 2007 Mustang GT Shelby BUT my old connector does not have the same colors as in the example. I have no white, no green and no red. Seems to me that red (power) is black and green (grouns) is black too. But white ? Thansk for your help.
|September 27th, 2015 12:30 PM|
|Tbones80||Finally got around to looking at it again. Have code p0581 cruise control circuit A high. Going to take apart my connection and resolder them. See if it makes any difference.|
|July 23rd, 2015 11:31 PM|
|08-045||2 questions, what step can I stop at if I only want the horn and cruise control to work? Also do I need to remove the U shaped horn piece if Im not worried about the other controls? The new wheel has the U shaped horn piece already in place. Thanks|
|May 5th, 2015 09:37 PM|
|Tbones80||Ya its brown and blue, and white is with the gray.|
|May 5th, 2015 04:24 PM|
|crackpotfox||I can't see the pic well, but I want to guess to try and help you out. I can't tell if its brown to blue or not in the first pic. Did you confirm all the wire colors to be correctly matched according to the op?|
|May 5th, 2015 12:37 AM|
|Tbones80||Bump, would really like to figure this out.|
|April 29th, 2015 06:03 PM|
|April 26th, 2015 02:36 PM|
OK here's the pics. Anyone see anything wrong?
1st pic is the 4 wires Ive soldered together from new harness to old connector.
2nd pic is the wires left over in the new harness along with the black wire eyelet that I am grounding on the small torx bolt.
3rd pic is everything, shows the green ground wire, with the green wire from from new harness soldered to it and I also put that black wire eyelet with it.
4th pic is the cruise control buttons with harness, just showing the wire colors that come out of it.
|April 25th, 2015 03:08 PM|
|acharmedmatrix||Ground is the same at all points of the vehicle so that should be fine. I believe you are the only one to get audio but not cruise. I'll check back for your pictures|
|April 25th, 2015 12:02 AM|
|Tbones80||Yes I've ground the black wire with an eyelet. Still doesn't work. The black wire is hooked with the green at the connector. Have the green hooked to the harness ground and the black to the small Allen bolt. Maybe should both be ground to same wire? I'll take pics this weekend and post them, see if you can find a hole in my wiring. All connections are soldered so shouldn't be a connection issue. Think I'm the only person here with no issues with audio but do with cruise control lol.|
|April 21st, 2015 02:02 PM|
I believe all of the cruise functions go through one wire and it uses different resistors to change up the signal. If your connection is not 100%, the resistance may not be what it is supposed to be and the computer is not recognizing the signal. Just a thought.
And I would ground the black wire with the eyelet. It sounds like it's set up as a ground wire.
|April 21st, 2015 11:00 AM|
|Tbones80||Yes I was testing on a highway. I'll double check that connection. If good I'll post some pics of my wiring then you can see if any things wrong.|
|April 21st, 2015 12:40 AM|
Before you go digging back in... you made sure to test the cruise while going over 35, right?
|April 19th, 2015 08:55 PM|
|Tbones80||Hey! No the green ground was on the audio side. And my stereo controls work perfect so I did that side correctly. Just can't figure out what I did wrong on the cruise side.|
|April 19th, 2015 08:16 PM|
|April 18th, 2015 03:20 PM|
|TTS197||Great write up. I can see this in my future... especially since my steering wheel is probably the most worn item in the car = (|
|April 18th, 2015 01:28 PM|
Sorry for the necro bump but I seem to have issues with the cruise control. It lights up with the headlights so power is there but cruise doesn't work. All the wires are soldered to the proper wires.
I'm thinking it may be my ground loop. On the ground bolt I have 3 wires. I have the green wire eyelet from old connector, the green from the new harness, and there's a black wire with an eyelet from the new harness also. I didn't see this wire on the writeup. Should this be grounded?
|This thread has more than 20 replies. Click here to review the whole thread.|