Modded Mustang Forums banner

1 - 20 of 125 Posts

·
Registered
Joined
·
4,372 Posts
Discussion Starter #1 (Edited)
i made a thread the other day similar but i want to know everyones numbers and what superchargers they have and their engine setups.. I am completely hooked on the idea of supercharging now. IM so sick and tired of driving my mustang. It's so damn slow lol. I might as well take the insurance off now and store it for the winter at this rate.

Post...

Manufacture of supercharger, Boost, RWHP, engine setup, Cost, etc

Thanks:D
 

·
Registered
Joined
·
6,139 Posts
Procharger, 7 lbs, trick flow plenum, 75mm throttle body, Mac o/r h pipe, Mac Catback.

368 hp/406 rwtq.
 

·
Boost gets you laid
Joined
·
2,625 Posts
old setup:

Procharger P1SC. stock midpipe, flowmaster catback, 10psi, 70mm TB/Plenum, 3 core race intercooler, 42lb injectors, svt focus pump, conservative tune. 380rwhp/380rwtq (mustang dyno)

car went [email protected] on 18" wheels and stock gears.. third pass ever down a track, 265 wide tires. stock rear suspension

new setup:

P1SC, forged shortblock, blower cams, dual GT Pumps, OD Crank Pulley, 2.8" blower pulley, 8 rib setup, 60lb injectors, longtubes, no cats, etc.. should make over 500rwhp easily.
 

·
Registered
Joined
·
16,245 Posts
427rwhp/415rwtq

mods in sig... 9#'s of boost

2600 or so in blower setup tune,guages, and all. (not cams/bolt ons)
 

·
Registered
Joined
·
16,245 Posts
bob.. i havent seen nor heard of a p1 getting over 500rwhp. That would be badass if you could.
 

·
Baker Jr.
Joined
·
3,472 Posts
370/380, mods are in my sig, bought it used for 2000, ended up with guages and misc parts and dyno tune total was 3000
 

·
MM's Ford Truck Guy
Joined
·
1,352 Posts
^ +1 Baker
 

·
Registered
Joined
·
374 Posts
vortech v-2 sq 10 psi mods in sig and hp i estimated it tho it 408 and 386. i run my 1/4th's on nittos pulling 1.9 60's not that great of a 60' but pretty fair!
 

·
Registered
Joined
·
4,987 Posts
In Short:
Stock Lighting specs at 8:4:1 Compression
380FWHP/450FWTQ

Stock long block 5.4, 9:0:1 Compression
Eaton M112 9Psi....
CAI
Exhaust
 

·
Registered
Joined
·
487 Posts
vortech v-2
intercooled
9lbs

70mm tb
42lbs injectors
90mm MAF
svt 255lb fuel pump

401hp/380tq
 

·
Registered
Joined
·
487 Posts
Vortech v3
non intercooled
9 lb

full exhaust and cats
75 tb
75 plenum
42 lb injectors
flowcharger (boost a pump)

350hp and 360 tq on mustang dyno
 

·
Registered
Joined
·
2,363 Posts
v2 13psi..6100 rpm
415whp393 torque
mods in garage mild tune will be pushing it a bit more in the future...looking to run 15psi..will be upgrading to the new vortech more efficent wheel which creates more low end boost....
i am ona 6rib..
 

·
Registered
Joined
·
16,245 Posts
turbo... what is this you speak of that is going to help with lower boost?
 

·
I Poop Entirely Way Too Much
Joined
·
8,720 Posts
Novi 2000, 14 psi, 416 hp 392 tq, Go tthe blower with intercooler for $2800.

I also have the Accufab 75mm TB an Plenum, Mac prochamber and catback and AFM power pipe and a Livernois forged 5L stroker.
 

·
Registered
Joined
·
2,363 Posts
baker, i talked with vortech and they have a upgraded wheel for the v2....for more low end boost....
so they tell me :)
 

·
Registered
Joined
·
4,372 Posts
Discussion Starter #18
how are you guys getting the cost under 3000 Minus all the bolt ons?

on vortec's site they have one on there for 2500 and i want mine to be intercooled and all the other little acssories you have to buy have got to add up to more then 500.00?

did you guys all buy your stuff used? and where is a good place to buy From?

How much are Prochargers, I dont see a price on their website?
 

·
Registered
Joined
·
374 Posts
baker, i talked with vortech and they have a upgraded wheel for the v2....for more low end boost....
so they tell me :)
I have this wheel on my v-2 works well 2 psi at 2100 rpms i launch at about 3800 rpms im making 350 rwtq there there torque at 5000k just hangs up at about 386 and barely drops to redline, same with the rwhp. Its alot more efficient.
 

·
I Poop Entirely Way Too Much
Joined
·
8,720 Posts
how are you guys getting the cost under 3000 Minus all the bolt ons?

on vortec's site they have one on there for 2500 and i want mine to be intercooled and all the other little acssories you have to buy have got to add up to more then 500.00?

did you guys all buy your stuff used? and where is a good place to buy From?

How much are Prochargers, I dont see a price on their website?
New blowers are around $4500, they push $6gs with a intercooler. You can get a ebay intercooler for like $300 i think, its a quality setup and a few guys on here use it, I have the CXRacing piping. Theres tons of used kits floating around though, thats the way to go.
 
1 - 20 of 125 Posts
Top