Modded Mustang Forums banner
Cancel
Create thread New Garage Forums

What Did You Do To Your Sixxer Today?

23 reading
Jump to Latest
Status
Not open for further replies.
5,401 - 5,420 of 19,030 Posts
#5,401 ·
Mr. Red Pony said:
Mines the same. But I never got axles so it wasn't a big deal. And I run 1.5" spacers in the back to compensate.
Click to expand...
i was going to run 3/4" spacers

will it be fine without spacers until i can get some?
 
Save
Like Like
#5,402 ·
i also have a 99-04 panhard bar to install, i wonder if it will fit now. ahhhh and now i have to buy wheel spacers, this really sucks
 
Save
Like Like
#5,404 ·
Skargon said:
I dont see why not, as long as nothing is Rubbing?
Click to expand...
well MM sells two different ones, one for 98 and earlier mustangs and one for 99-04. I sent them an email to see if they know. Maybe i will just sell it

now i have to go buy some new drill bits because i dont have a 14mm one to drill the holes out.
 
Save
Like Like
#5,405 ·
SkylineR32420 said:
Some Plastic from an old remote, a couple allen head screws, a dremmel, old 3 way switch found in garage, and a small piece of shrink tubing, i did what the stereo shop said wouldn't werk!!! and looks half way decent, way cheaper than a 125.00 replacement from ford!!!
Image

Image
Click to expand...
What is the switch for?

southfour said:
8.8 is mostly in
Image
Click to expand...
whats the red bar?

Mr. Red Pony said:
I wish that too. But luckily I can just do mine at work after hours. :D
Click to expand...
ahhh lucky S.O.B :llama
 
Save
Like Like
#5,410 ·
Got the Passenger side Outer Tie Rod Done.
Taking a Break because I Pinched the **** out of my Finger. :D

Other then that, I Got it done pretty easily.. Couldnt BUDGE the Nut on the back, So I made sure my New Tie Rods were the same exact length, And Put it where it was. Tightened everything up, Torqued it to what the book said, Sat her down; No more wheel Wobble.. Glad its done, One to go. :D
 
#5,414 ·
ordered wheel spacers and new axles

having a hell of a time finding a 14mm drill bit thought

Mr Red pony, did you use a 14mm or a 9/16" bit when you drilled the holes out?
 
Save
Like Like
#5,415 ·
southfour said:
ordered wheel spacers and new axles

having a hell of a time finding a 14mm drill bit thought

Mr Red pony, did you use a 14mm or a 9/16" bit when you drilled the holes out?
Click to expand...
For the LCAs? I used the biggest one I had (3/8) and walked it around until the hole was big enough. Try a uni-bit. (the tapered one that steps up until the bolt just fits.
 
Save
Like Like
#5,416 ·
I talked to the Midas guy about welding Dual Exhaust.

He said if I were to cut the old Muffler off myself, And Cut the Pipes at the cat's, welding new mufflers in would only cost about 50$ with New Hangers.

I'm planning on doing it cheap.
Glasspacks. :D
Any Recomendation's on glasspacks?
 
#5,417 ·
To not get them? D:
 
Save
Like Like
#5,419 ·
Agreed glass packs=nasty. found that mac flopaths are one of the better sounding mufflers and decently cheap. :new member by the way(first post ha):

Just put H&r SS springs and left off the iso today no more rock crawling for me :(
 
Save
Like Like
5,401 - 5,420 of 19,030 Posts
Status
Not open for further replies.
You have insufficient privileges to reply here.
About this Discussion
19K Replies
342 Participants
Last post:
slonison
Modded Mustang Forums
posts
6.3M
members
83K
Since
2005
A forum community dedicated to all Ford Mustang owners and enthusiasts. Come join the discussion about performance, racing, builds, modifications, troubleshooting, maintenance, and more!
Full Forum Listing
Explore Our Forums
96 - 04 Modular Mustangs 5.0 Mustangs New Members Introductions Classic Mustangs